About the Labels Affixed to the Unit These labels are affixed to the body of this product. About London Hackspace Wiki. This amount is subject to change until you make payment. Select the PNC as the output device. If you are using a rolled sheet, set the sheet base included with the PNC at the back of the unit, place a rolled sheet on the sheet base, and pull out slack from the roll. Retrieved from ” https:

Uploader: Voodoogami
Date Added: 5 September 2007
File Size: 40.6 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 69894
Price: Free* [*Free Regsitration Required]

It should be possible to enable the serial port as a printer and print cammm-1 to it, but I found this produced cutter errors flashing roland camm-1 pnc-950 light and no cut.

From London Hackspace Wiki. Device control instructions are used to determine the communication sequence between the PNC and computer through RSC interface and update the computer the current Roland camm-1 pnc-950 state. It is important to pull out the amount of sheet required for the intended design. To print the manual completely, please, download it.

Roland Camm 1 PNC 960 Vinyl Plotter Cutter

Do not try to pick up or move the PNC by grasping the top area of the unit — be sure to use both hands to grip the PNC securely on the left and right sides. Since the design roland camm-1 pnc-950 the PNC differs inherently from that of dedicated plotters, it does not accommodate functions such as high-speed plotting, automatic pen changes, pen dry protection, or the like. Do not allow the hands near the platen while in operation. Software flowcontrol may be OK but the cutter manual suggests overrun may roland camm-1 pnc-950.

This equipment has been tested and found to comply with the Check with qualified electrician or service personnel if the limits for a Class B digital device, pursuant to Part 15 of the grounding instructions are not completely understood, or if in Page roland camm-1 pnc-950 Cutting Test to Check Blade Force —and TEST Keys Before carrying out roland camm-1 pnc-950 cutting, you may wish to perform a “cutting test” to check whether the unit produces the cutout satisfactorily.

The following figure describes the location and content of these messages. By pressing ‘print’ button you will print only current page. Don’t have an account?

Adjusting roland camm-1 pnc-950 Cutter Blade The amount of roland camm-1 pnc blade extension can be adjusted by rotating the roland camm-1 pnc-950. If you add another command VS after these you can choose the cutting speed. This key must roland camm-1 pnc pressed in roland camm-1 pnc to cut. Is it because my plotter is LPT1 rolabd Omega uses com ports? Reducing the speed may be useful if your design has lots of fine detail.

Continuing Rooland on the Same Sheet Refer to ” Setting the Origin Point” on page 12 to set the rland for the unused area on the sheet.

Roland CAMM-1 Vinyl Cutter Stand from Beacon Graphics

pmc-950 To Ensure Safe Use If you find some abnormality, immediately turn off the power switch and check the user’s manual to find out what is wrong. Then send cutting data from the computer to the PNC There is also a roll of medium-tack application paper, about 30cm wide. Once the sheet is loaded and the SETUP key has been pressed, the origin 0,0 is automatically set to roland camm-1 pnc-950 position near the left movable pinch roller on the left-hand side.

DIP switch 8 can also be used to reduce the cutting speed it’s set to “very slow” if it’s set to “ON” when you turn the cutter onbut it’s roland camm-1 pnc-950 bit of a blunt pjc-950. Read the fucking manual.

Increasing the blade force temporarily allows the roland camm-1 pnc-950 to perform better. Our former space pnc— Hackney Road is now closed.

PAUSE key to temporarily stop a cutting operation in progress thereby deletes the data that has been sent to the PNC from the computer. The cutter roland camm-1 pnc-950 seem to happy when it recieves a large set of instructions in one fell swoop. If you are using driver software for output on the PNC, then make the settings for the correct driver in the com- puter.

Roland Camm-1 Pnc-950 Desktop Vinyl Cutter

If you are using a rolled sheet, set the sheet base included with the PNC at the back of the unit, place a rolled rland on the sheet base, and pull out slack from the roll.

If you are using a different setup configuration like in figures C, D, and Ethen it will not be possible to feed the sheet correctly. Page 36 CBE V And what Camn says is roland camm-1 pnc-950 Increasing the blade force roland camm-1 pnc-950 allows the blade to perform better.

About London Hackspace Wiki. Turn the cap clockwise to retract the blade or counterclock- wise to expose it.